KF-S1 spiral bevel series

Steel housing and output shaft
Output shaft smooth
Ratio 1:1 and 2:1 (spiral bevel)
Torque 24 – 1300 Nm

Black coated steel housing, aluminum output and motor adapter flange
Steel output shaft, smooth
Spiral bevel gear design
Nominal torques:
- T_2N : 24 Nm - 1.300 Nm
Ratios
- 1-stage : 1 / 2
Low backlash
- 1-stage : ≤ 3 arcmin
High efficiency
- 1-stage : ≥ 97%
Easy mount
High accuracy
The output shaft rotates in the same direction as the servomotor
Available sizes: KF060 / KF075 / KF100 / KF140 / KF180 / KF210 / KF240

KF		Stage	Ratio⁽¹⁾	KF 060	KF 075	KF 100	KF 140	KF 180	KF 210	KF 240
Nominal output torque T_2N	Nm	1	1	25	45	78	150	360	585	1,300
Nominal output torque T_2N	Nm	1	2	24	42	68	150	330	544	1,220
Emergency stop torque T_2NOT	Nm	1	1	2 times of nominal torque T_2N
Max. Acceleration torque T_2B	Nm	1	1~2	1,5 times of nominal torque T_2N
No load running torque ⁽²⁾	Nm	1	1~2	0.3	0.3	1.5	1.7	5.5	9	20
Backlash ⁽³⁾	arcmin	1	1~2	≤3	≤3	≤3	≤3	≤3	≤3	≤3
Torsional rigidity	Nm/arcmin	1	1~2	0.8	3.5	9	20.5	44	80	168
Nominal input speed n_1N	rpm	1	1~2	6,500	4,500	3,500	2,000	1,500	1,200	1,000
Max. input speed n_1B	rpm	1	1~2	7.500	6,500	5,500	4,500	3,500	3,000	2,200
Max. radial load F_2rB ⁽⁴⁾	N	1	1~2	5,400	7,700	11,100	15,100	26,100	36,400	46,900
Max. axial load F_2aB ⁽⁴⁾	N	1	1~2	2,700	3,850	5,550	9,050	14,550	18,200	23,450
Max. tilting moment M_2k	Nm	1	1~2	390	630	1,100	2,230	5,020	6,430	10,810
Operating temperature	°C	1	1~2	0° C ~ +90°C
Degree of Protection		1	1~2	IP65
Lubrication		1	1~2	Synthetisch lubrication grease
Mounting position		1	1~2	All directions
Running noise ⁽⁵⁾	dB (A)	1	1~2	≤68	≤70	≤74	≤76	≤77	≤78	≤80
Efficiency n	%	1	1~2	≥97%

Overbrengverhouding ( i = N in / N out ) Ratio ( i = N in / N out )
Backlash is measured at 2% of Nominal output torque T_2N
These values are measured by gearbox with ratio = 2 (1-stage) at 3.000 rpm without load.
Applied to the ourput flange center at 100 rpm.
These values are measured by gearbox with ratio = 2 (1-stage) at 3,000 rpm no loading.
By lower ratio and/or higher RPM, the noise level could be 3 to 5 dB higher.

Maximum tilting moment::

Size		KF060	KF075	KF100	KF140	KF180	KF210	KF240
Z2 (mm)		104.4	119.3	144.3	178	251.9	253.9	330.8

Applied to the ourput flange center at 100 rpm.

Maximum radial and axial loads:

The maximum radial and axial loads on the output shaft of the gearbox depends on the design of the gearbox supporting bearings.
Apex Dynamics uses the extension straddle oversized ball bearing design. This can take heavy load from both axles

Permitted radial load F2r on center of output shaft X = ½ x L for various output speeds.

If radial force F2r is not exerted on the center of the ouput shaft X < ½ x L or X > ½ x L, the permitted radial and axial loads can be calculated by the position load factor Kb on the above diagram.

Model No.		KF 060	KF 075	KF 100	KF 140	KF 180	KF 210	KF 240
Ø ^(A) (C3)		1-stage	1-stage	1-stage	1-stage	1-stage	1-stage	1-stage
8	kg*cm²	0.10	-	-	-	-	-	-
11		0.17	0.18	-	-	-	-	-
14		0.21	0.50	-	-	-	-	-
19		0.62	0.63	1.69	-	-	-	-
24		-	4.49	4.89	5.05	-	-	-
28		-	-	6.14	6.55	-	-	-
32		-	-	8.54	9.47	10.18	-	-
35		-	-	13.86	14.91	15.21	15.68	23.46
38		-	-	18.87	20.69	20.7	21.69	23.46
42		-	-	-	22.58	22.83	23.59	25.28
48		-	-	-	55.45	58.45	25.40	61.61
55		-	-	-	-	-	61.02	89.67
60		-	-	-	-	-	-	112.49

(A) Ø Input shaft diameter

KF-S1 / S2 -spiral bevel:

	KF 060	KF 075	KF 100	KF 140	KF 180	KF 210	KF 240
	1-stage	1-stage	1-stage	1-stage	1-stage	1-stage	1-stage
D1	68	85	120	165	215	250	290
D2	5.5	6.6	9	11	13.5	17	17
D3 h6	16	22	32	40	55	75	85
D4 g6	60	70	90	130	160	180	200
D5	18.5	25.8	36.8	55.2	69.2	82.2	92.2
D6	M5x0.8P	M8x1.25P	M12x1.75P	M16x2P	M20x2.5P	M20x2.5P	M20x2.5P
D8	64	72	92	116	156	195	240
L1	62	76	101	141	182	215	245
L2	28	36	58	82	82	105	130
L3	20	20	30	30	30	38	40
L4	2	2.5	3	3	3	3	3
L5	25	32	50	63	70	90	125
L6	2	2	4	5	6	7	3
L7	6	7	10	12	15	17	20
L9	4.8	7.2	10	12	15	15	15
L10	12.5	19	28	36	42	42	42
L11	50	58	67.5	88	127	131.5	169
L12	46.5	52.5	61.5	76	97.5	105.5	141
L13	144.5	166.5	217	276	336.5	380	480
L16	81.5	97	113.5	147.5	196.5	229	260
B1 h9	5	6	10	12	16	20	22
H1	18	24.5	35	43	59	79.5	90

(1) Dimensions are related to motor interface. Please contact Apex Dynamics for details.

Model No.	Dimension	D1	D2	D3	H1	H2	Screw⁽¹⁾	Ta ⁽²⁾	J	Order Code
Model No.	Dimension	D1	D2	D3	H1	H2	No. x type	(Nm)	(kg.CM²)	Order Code
KF 060	SSD-d18xdw15	44	18	30	15	18.5	5 x M5	4	0.4	SSD-18
KF 075	SSD-d24xdw20	50	24	36	19.5	23	6 x M5	4	0.8	SSD-24
KF 100	SSD-d36xdw30	72	36	52	23.5	27.5	5 x M6	12	3.9	SSD-36
KF 140	SSD-d50xdw40	90	50	70	27.5	31.5	8 x M6	12	11.2	SSD-50
KF 180	SSD-d68xdw55	115	68	86	30.5	34.5	10 x M6	12	30.9	SSD-68